Plumbing - York Region Hot Tub and Leisure

Shopping Cart
905-773-7721
Go to content

Plumbing

15-2005035
2" Gate Valve Safety Clip

Use this clip to ensure your gate valves remain open.
$ 0.99(HST excl.)
Add
15-2005036
2.5" Gate Valve Safety Clip
Use this clip to ensure your gate valves remain open.
$ 0.99(HST excl.)
Add
15-4505003
2" Gate Valve Seal Rings
This set of gate valve seal rings can be used to repair a 2" gate valve that has 4 bolts holding it together.
$ 6.99(HST excl.)
Add
15-4505101
Floor Escutcheon -
These small plastic sleeves were used in the floor drain of the Hydropool Self Clean System.
$ 0.99(HST excl.)
Add
15-4505102
2.5" Gate Valve Seal Rings
This set of gate valve seal rings can be used to repair a 2.5" gate valve that has 4 bolts holding it together.
$ 8.99(HST excl.)
Add
15-4510020
Waterway Spa Drain Gasket -
This is a replacement gasket that is used on the Waterway Spa Drain
$ 1.99(HST excl.)
Add
15-5005004
3/8" Barbed Tee
$ 1.99(HST excl.)
Add
15-5005033
2.5"S x2.5"S x1.5"S Tee

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 7.99(HST excl.)
Add
15-5005035
2.5"S x2.5"S x2"S Tee

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 12.99(HST excl.)
Add
15-5010003
1" Cap
Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.
A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.
A Plug acts as a male end and will fit into the pipe or the fitting
$ 0.99(HST excl.)
Add
15-5010004
1.5" Cap
Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.
A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.
A Plug acts as a male end and will fit into the pipe or the fitting
$ 1.99(HST excl.)
Add
15-5010005
2" Cap

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 1.99(HST excl.)
Add
15-5010006
2.5" Cap

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 9.99(HST excl.)
Add
15-5015001
1.5" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 0.99(HST excl.)
Add
15-5015002
1" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 0.99(HST excl.)
Add
15-5015003
1/2" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 0.99(HST excl.)
Add
15-5015004
2.5" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 3.99(HST excl.)
Add
15-5015005
2" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 2.99(HST excl.)
Add
15-5015007
3" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 4.99(HST excl.)
Add
15-5015008
3/4" Coupling SXS (Slip X Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
$ 2.99(HST excl.)
Add
15-5020003
1.5" Elbow 90 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5020004
1.5" Elbow 90 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5020005
1.5" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5020006
1" Elbow 90 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5020007
1" Elbow 90 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 2.99(HST excl.)
Add
15-5020008
1/2" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5020009
1/2" Elbow 90 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5020010
1/2" Elbow 90 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5020013
2.5" Elbow 90 Degree SXS(Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 8.99(HST excl.)
Add
15-5020014
2.5" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 9.99(HST excl.)
Add
15-5020017
2" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 2.99(HST excl.)
Add
15-5020018
2" Elbow 90 Degree SXS(Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 2.99(HST excl.)
Add
15-5020020
2" Elbow 90 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 6.99(HST excl.)
Add
15-5020022
3" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 12.99(HST excl.)
Add
15-5020023
3" Elbow 90 Degree SXS(Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 10.99(HST excl.)
Add
15-5020024
3/4" Elbow 45 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5020025
3/4" Elbow 90 Degree SXS (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in
$ 0.99(HST excl.)
Add
15-5020026
3/4" Elbow 90 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5020029
1.5" Elbow 45 Degree SXSPG(Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5020030
2" Elbow 45 Degree SXSPG (Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5020031
1" Elbow 45 Degree SXSPG (Slip x Spigot)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5020034
2" Elbow 90 Degree SXS Sweep (Slip X Slip)

Sweep means it has a softer bend to allow water through easily to ensure a proper flow.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5020035
2" Elbow 90 Degree SXSPG Sweep (Slip X Spigot)

Sweep means it has an easier bend to ensure water is flowing properly and more consistently.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5035001
1.5" Plug

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 1.99(HST excl.)
Add
15-5035002
1" Plug
Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.
A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.
A Plug acts as a male end and will fit into the pipe or the fitting
$ 1.99(HST excl.)
Add
15-5035003
1/2" Plug

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 0.99(HST excl.)
Add
15-5035004
2" Plug

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 2.99(HST excl.)
Add
15-5035005
3/4" Plug

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 1.99(HST excl.)
Add
15-5035007
3/4" Barbed Plug

Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.

A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.

A Plug acts as a male end and will fit into the pipe or the fitting
$ 0.99(HST excl.)
Add
15-5035011
Waterway Smart Plug -
Used specifically for Waterway Water manifolds.
Cap Vs. Plug –Both items are used to create a dead end at the end of a pipe or fitting.
A Cap is used as a female end whereas the pipe will slide into the cap. The cap will fit over the pipe to be glued into place.
A Plug acts as a male end and will fit into the pipe or the fitting
$ 0.99(HST excl.)
Add
15-5040002
1"SPG x 1/2"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5040003
1"SPG x 3/4"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5040004
1.5"SPG x 1"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5040005
1.5"SPG x 3/4"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5040006
2.5"SPG x 2"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5040007
2"SPG x 3/4"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5040008
2" SPG x 3/4" FIPT Reducer Bushing (Spigot X Female Pipe Thread)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.

"FPT" "FIPT" all mean the same thing. Female Pipe Thread.
$ 2.99(HST excl.)
Add
15-5040010
2"SPG x 1.5"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5040011
2"SPG x 1"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5040012
3"SPG x 2.5"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 4.99(HST excl.)
Add
15-5040013
3"SPG x 2"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 4.99(HST excl.)
Add
15-5040014
3/4"SPG x 1/2"S Reducer Bushing (Spigot X Slip)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 2.99(HST excl.)
Add
15-5040018
1.5" SPG x 3/4" FIPT Reducer Bushing (Spigot X Female Pipe Thread)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.

"FPT" "FIPT" all mean the same thing. Female Pipe Thread.
$ 1.99(HST excl.)
Add
15-5040101
2" FIPT x 2" SPG Reducer Bushing (Female Pipe Thread X Spigot)

Reducer Bushing – A pipe fitting that extends a run by joining two pipes of different diameter. Usually has a male and female ends either of which may be threaded.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.

"FPT" "FIPT" all mean the same thing. Female Pipe Thread.
$ 2.99(HST excl.)
Add
15-5045001
1.5" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5045002
1" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 2.99(HST excl.)
Add
15-5045003
1/2" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5045004
1"x1"x1/2" Reducer Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 1.99(HST excl.)
Add
15-5045005
2.5" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 12.99(HST excl.)
Add
15-5045006
2" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5045007
2"x2"x1.5" Reducer Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5045008
2"x2"x1" Reducer Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 3.99(HST excl.)
Add
15-5045009
3" Tee SxSxS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 15.99(HST excl.)
Add
15-5045010
3/4" Tee SXSXS (Slip x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 0.99(HST excl.)
Add
15-5045012
2"x2"x1/2" Reducer Tee SPxSxS (Spigot x Slip x Slip)

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 4.99(HST excl.)
Add
15-5045017
2.5" Sanitary Tee SxSxS (Slip x Slip x Slip)



"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 21.99(HST excl.)
Add
15-5065001
1.5" Ball Valve
$ 18.99(HST excl.)
Add
15-5065004
1.5" SXS Gate Valve (Slip X Slip)
Gate Valve 1 1/2" PVC Gate Valve S x S
Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.
"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 17.99(HST excl.)
Add
15-5065005
2.5" SXS Gate Valve (Slip X Slip)

Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 53.99(HST excl.)
Add
15-5065023
2" SXS Gate Valve (Slip X Slip)
Gate Valve 2" PVC for 2005 to Present
Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 12.99(HST excl.)
Add
15-5065024
2.5" SXS Gate Valve (Slip X Slip)

Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 26.99(HST excl.)
Add
15-5065045
2" SXSPG Gate Valve (Slip X Spigot)

Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.

"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.

"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 12.99(HST excl.)
Add
15-5065046
2.5" SXSPG Gate Valve (Slip X Slip)
Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose.
"Slip" "Slip Socket" and "Socket" all mean the same thing. The pipe glues into it. A 'female' end. The exception to this is a "Slip T" in which case the "Slip part" slides over pvc pipe.
"St" "Street" "Spg" and "Spigot" all mean the same thing. It glues into another fittings socket. A 'male' end. Note: There are both threaded street fittings and glue in street fittings. The street, spigot, st or spg just refers to the mechanism, not whether it's threaded or glued in.
$ 26.99(HST excl.)
Add
15-5065051
1" Ball Valve
$ 15.99(HST excl.)
Add
15-5065053
2" Ball Valve
$ 41.99(HST excl.)
Add
15-5065055
3/4" Ball Valve
$ 9.99(HST excl.)
Add
15-5555222
Spa Drain Assembly -
You can simply attach a standard garden hose to the end of this drain to easily drain your spa.
$ 18.99(HST excl.)
Add
15-5555271
Ice Bucket Drain -
This Ice Bucket Drain was used by Hydropool from 2010 up to and including 2013.
$ 3.99(HST excl.)
Add
15-5555272
Spa Drain Assembly -
You can simply attach a standard garden hose to the end of this drain to easily drain your spa.
$ 14.99(HST excl.)
Add
15-5555290
Spa Drain Assembly -
Simply attach your garden hose and let gravity drain your spa.
$ 14.99(HST excl.)
Add
15-6040005
200 GPM Grey Plastic Suction
2" Plumbing connection
Grey Plastic Face
$ 19.99(HST excl.)
Add
15-6040009
200 GPM Stainless Steel Suction
2" Plumbing connection
Stainless Steel Face
$ 34.99(HST excl.)
Add
15-6040018
200 GPM Grey Plastic Suction 2.5Inch -
200 GPM Grey Plastic Suction
2.5" Plumbing connection
Grey Plastic Face
$ 16.99(HST excl.)
Add
15-6040019
Low Profile Drain -
This Low Profile Drain has a 3/4" barbed end so that the waterline can be clamped on.
$ 13.99(HST excl.)
Add
15-6040025
120 GPM Suction
2" Plumbing connection
Black Face
$ 16.99(HST excl.)
Add
15-6040032
Low Profile Drain -
This Low Profile Drain has a 3/4" socket end so that the waterline can be glued in.
$ 12.99(HST excl.)
Add
9057737721
Back to content